from New Micros, Inc

Last updated: 10 May 2004

TiniARM™ module

APPLICATIONS:

TiniARM™ is suitable for dedicated control of RC Servo motors, DC motors, Brushless DC motors, stepper motors, solenoids, and other bipolar power outputs, such as general converter/inverter applications, data collection and many networked control applications.

FEATURES:

• Board Size: 1.0"(W) x 1.3"(L) x 0.4"(H)
  25mm(W) x 33mm(L) x 10mm(H)
• Weight: 0.2 Ounces
• Programming Language:
  • MPE Forth, Resident language. This is very similar to the implementation on the MPE USB Stamp.
  • GNU, download info and examples now available
  • In-System Programming Flash Utility (free download)
• ARM7TDMI-S CPU, 32-bit microprocessor
• CPU oprerating range 10MHz to 60Mhz
• Real Time Clock
• On-chip Memory
  • 128KByte Program Flash
  • 64KByte Static Ram
• 16 General Purpose Digital I/O lines share functions with,
  • 4-wire SPI Interface
  • 4 PWM channels(3 on 24-pin connector, 1 shared with Jtag signal on other connector )
  • 7 Timers
  • 1 SCI (TTL) channel with the addition of a modem interface
  • 3 external Interrupts
• Two Serial Communication Interface (SCI)
  • UART0 is dedicate for RS-232 serial channel
  • UART1 is TTL signals and shared function with GPIOs
• I2C Serial Interface
• JTAG connection for flash programming/debugging
• Two low power modes, Idle and Power down
• WatchDog Timer
• Onboard three user's leds
• Onboard 5.0V, 3.3V, & 1.8V linear regulators
• 2x12 header pin connector for Power, Serial, and I/O's connection

Development of the user programming in internal Flash is through an RS232 Serial Communnication Interface, or by JTAG connections to the host. TiniARM™ makes a very cost effective solution.

Accessories required:

• Serial Cable
• 6-12Vdc @ 100mA or higher

Price 1 off: GBP 49.00, USD ~62, EU ~52.
Please contact MPE for details of volume pricing. Please note that boards are supplied as hardware only with an on-board Forth system. Schematics and other manuals may be downloaded from New Micros.

TiniARM™ DevKit

The TiniARM™ Development Kit is an ideal kit to add your own components such as Sensors, Sonars, H-Bridges, Opto-Isolators, Leds, etc. These surround the TiniARM™ controller which plugs into the center of the carrier board to provide an inexpensive and quick turnkey prototype for use in Automation, Robotics, Motion Control, and Industrial Control.

FEATURES:

• TiniARM module as above
• Size: 4.0" x 4.0"
• Plug-in connectors which are compatible for use with
TiniARM™, TiniPod™, and PlugaPod™.
• Prototype area surrounding the TiniARM™ I/O connectors
• Standard DB9 Serial Connection
• 5V & 3.3V regulators on Carrier Board
• Power On/Off switch
• Power indication Leds
• Controller Reset Switch

Accessories included:

• Serial Cable

Price 1 off: GBP 69.00, USD ~124, EU ~102.
Please contact MPE for details of volume pricing.

Please note that boards are supplied as hardware only with an on-board Forth system. Schematics and other manuals may be downloaded from New Micros.

TiniARM™ DevKit Plus

DevKit Plus - As the Development Kit but wth an MPE VFX Forth Cross Compiler and all source code for the on-board Forth for the USB Stamp and the TiniARM™. The compiler is limited to 120k of code and 64k of RAM. This compiler generates code that is much faster and significantly smaller than the code produced by the on-board Forth's compiler.A rebate of GBP 100.00 is available when upgrading to the full version of the cross compiler.

Price: GBP 165.00, USD ~297, EU ~245
A rebate of GBP 100.00 is available when upgrading to the full version of the cross compiler.